行业新闻
Industry News
HOME  >  NEWS  >  Industry News
Maintenance and upkeep of multi-stage centrifugal blower
Time:2026-11-18 Size

The maintenance and upkeep of multi-stage centrifugal blowers need to be controlled in stages according to the cycle, with the core focus on lubrication, cooling, and vibration monitoring, which can significantly extend equipment life and reduce the risk of sudden shutdown.

📅 Classification cycle maintenance standard

Daily inspection: Record all instrument data, monitor internal abnormal noises, check that the oil pressure is stable at 0.5-0.7kg/cm ², and confirm that there are no abnormal fluctuations in the inlet and outlet air pressure.

Weekly inspection: check the oil level in the fuel tank, clean the filter screen, check the effectiveness of the safety valve, and clean the air inlet filter device.

Monthly maintenance: Clean the dust on the surface of the impeller, check the fastening status of the fasteners, and check that the insulation resistance of the motor is ≥ 1M Ω.

Quarterly minor repair: Check the wear of the bushing, clean the scale on the cooler, and calibrate the opening of the inlet and outlet valves.

Annual overhaul: Disassemble and inspect the entire machine, clean the attachments on the casing and rotor, perform dynamic balance correction on the impeller, and replace all seals.

124d2323c69c174b9069f38d965685e2.jpg

🛢️ Special management of lubrication system

Lubricating machine model: Replace the lubricating grease every 500 hours of operation, with the filling amount controlled at 1/3~1/2 of the bearing cavity, and excessive filling is prohibited.

Thin oil lubrication model: Before testing, add 32/46 turbine oil and filter it in advance. Change the oil after the first 200 hours of operation, and replace it every 3 months thereafter. Keep the oil level within the range of the oil gauge.

It is prohibited to mix different grades of lubricating oil, and the residual old oil inside the oil tank must be thoroughly cleaned when changing the oil.

The oil change cycle under high temperature conditions is shortened to 1.5-2 months, and replaced with high temperature specific extreme pressure gear oil to avoid oil oxidation and failure.

🌡️ Temperature and cooling system control

During normal operation, the bearing temperature should be maintained at 30-45 ℃, the outlet oil temperature of the bearing should not exceed 65 ℃, and the motor housing temperature should be ≤ 80 ℃.

The cooling water pressure of water-cooled models must be lower than the oil pressure. In summer, the inlet water temperature should be controlled within 30 ℃, and the scale in the cooling pipeline should be cleaned every half month.

Regularly clean the dust accumulation on the motor cooling fins of air-cooled models to avoid overheating and tripping of the motor due to heat dissipation failure.

❄️ Key points for operation and maintenance under extreme working conditions in winter and summer

Summer high temperature: Long term full load operation of the fan is prohibited. It is recommended to shut down for 30 minutes to naturally dissipate heat after continuous operation for 8 hours. The computer room should be equipped with exhaust fans to enhance ventilation.

Winter low temperature: Replace the low-temperature special lubricating grease, manually rotate the wheel several times before starting up to loosen the solidified grease, preheat for 3-5 minutes without load, and then run with load.

Regularly rotate the spindle 180 ° during long-term shutdown to avoid long-term static bending of the spindle, and do a good job of pipeline antifreeze and insulation in low-temperature environments.

⚠️ Core component maintenance specifications

Impeller: Check whether the rivets are loose and whether there are cracks in the welds during each major overhaul. After cleaning the scale, perform dynamic balance correction and control the vibration speed at ≤ 4.0mm/s.

Bearing: Choose SKF or FAG brand bearings, with a normal service life of up to 50000 hours. Replace immediately in case of abnormal vibration or noise.

Before lifting the rotor, all sealing components must be removed first. During the lifting process, protect the shaft neck, gears, and coupling parts to avoid collisions and scratches.

📊 Quick disposal of common faults

Vibration exceeding the standard: Prioritize investigating rotor imbalance, bearing wear, and loose foundation, and locate the fault point through a vibration analyzer.

Insufficient flow pressure: Clean the blockages in the inlet and outlet pipelines, check the wear of the impeller, and correct the opening of the inlet and outlet valves.

Shandong Ruidian Environmental Protection Technology Co., Ltd. is located in the high-end equipment manufacturing base of Luozhuang District, Linyi City. It is a modern enterprise that focuses on the research and development, design, production, and manufacturing of multi-stage centrifugal blowers, centrifugal vacuum pumps, Roots blowers, pneumatic conveying systems, and soil remediation integrated special equipment. Its telephone number is 13287120066.

The various information published on this website is for reference only and does not represent the position or viewpoint of this website. It does not constitute any investment, medical, legal or decision-making advice. Any actions taken by users based on the information on this website are at their own risk, and this website does not assume any direct or indirect responsibility. This website does not assume any responsibility for the authenticity, accuracy, completeness, or legality of its content.